What this chainring is and who it fits
The SRAM X-Sync Steel Direct Mount Chainring 28T Boost 3mm Offset is a steel 1x replacement ring built around the same X-Sync tooth profile as SRAM's pricier rings. The catalog describes it as the cost-conscious option with added durability from steel, and it is listed as compatible with all SRAM 1x cranks.
That compatibility statement is the key starting point. Before you buy or book workshop time, confirm your crank is a SRAM 1x direct mount unit. The supplied information does not list individual crank model numbers, so if you are unsure which generation or interface your crank uses, check the crank markings or ask the shop before ordering.
The specs that drive the install
- X-Sync Steel Direct Mount Chainring 28T Boost 3mm Offset: Compatible with all SRAM 1x cranks. This is the primary fit check: the ring is intended for SRAM 1x direct mount cranks, not for 2x setups or other mounting standards.

X-Sync Steel Direct Mount Chainring 28T Boost 3mm Offset - X-Sync Steel Direct Mount Chainring 28T Boost 3mm Offset: 28T tooth count with Boost 3mm offset. The 28T size and 3mm offset define the gearing and chainline position, so they need to match your frame and drivetrain plan before installation.
- X-Sync Steel Direct Mount Chainring 28T Boost 3mm Offset: Steel construction with SRAM X-Sync technology. Steel is the durability-focused choice, and X-Sync is the tooth profile that helps keep the chain engaged on a 1x setup.
Installation sequence
- 1. Confirm the crank interface: Check that your crank is a SRAM 1x direct mount model. The supplied catalog states compatibility with all SRAM 1x cranks, but does not list every model, so verify the direct mount fitting on your own crank before removing anything.
- 2. Remove the old ring: Take off the existing direct mount ring using the removal method your crank requires. The supplied information does not include a step-by-step removal procedure, so follow the crank manufacturer's instructions rather than guessing at tooling.
- 3. Clean the mounting interface: Wipe the crank spider or direct mount splines clean before fitting the new ring. A clean mating surface helps the ring sit flat and avoids trapped grit.
- 4. Fit the 28T ring with the 3mm offset oriented correctly: The ring is marked as Boost 3mm offset. Position it so the offset faces the direction that produces the intended chainline for your Boost frame. The supplied record does not include a diagram, so if the orientation is not obvious, check SRAM's crank documentation for your specific model.
- 5. Tighten the mount: Secure the ring using the fasteners and torque figure specified for your crank. The supplied product record does not include a torque value, so do not rely on a generic number; use the crank manufacturer's specification.
- 6. Check chainline and clearance: With the ring fitted, check that the chain runs cleanly through the ring and that there is clearance between the ring and the frame. The 3mm offset is there to set the Boost chainline, so this is the checkpoint that confirms the ring is seated and oriented as intended.
- 7. Spin and load-test: Rotate the cranks and run through the gears before riding hard. Listen for rubbing and watch that the chain stays engaged on the X-Sync teeth.
Checks worth making before you tighten the bolts
- Chainring size vs. frame clearance: A 28T ring is small, but clearance still depends on your frame and chainstay shape. The supplied information does not give a minimum clearance figure, so check physically with the ring in place.
- Boost frame and 3mm offset: The 3mm offset is part of the Boost chainline story. If your frame is not Boost-spaced, this ring may not put the chain where you need it; the catalog does not list non-Boost compatibility.
- Chain and cassette match: The ring is a 1x X-Sync ring, so pair it with a 1x drivetrain. The supplied record does not specify chain or cassette compatibility beyond the SRAM 1x crank statement, so confirm your chain is suitable for a 1x ring.
What the catalog does not tell you
The supplied product record confirms crank compatibility, tooth count, offset, and construction, but it does not include a torque specification, a chainline measurement, or a step-by-step removal and fitting procedure. Those details live with your crank manufacturer's documentation, not with this chainring listing.
That is not a reason to avoid the ring; it is a reason to have the right reference open when you install it. Treat the catalog facts as the fit and identity check, and treat the crank documentation as the source for tightening and chainline setup.


