Tilbage til blog
Vejledninger 2026-11-17 fullertonbicycle 0 visninger

Öhlins RXF 36 Coil Spring: How to Choose and Fit the Right Rate

Öhlins RXF 36 Coil Spring: How to Choose and Fit the Right Rate

Pick the right Öhlins RXF 36 coil spring rate, confirm fork compatibility, and plan a clean spring swap with the seven rates Fullerton Bicycle stocks.

Start with the fork, not the spring

The Öhlins RXF 36 Coil Fork Spring is a replacement spring for one specific fork family, so the first checkpoint is compatibility, not spring rate. The supplied catalog record states plainly that the spring fits the Öhlins RXF Coil fork only. If your fork is an air-sprung RXF 36 or a different coil model, this part is not the answer.

Once you have confirmed an RXF Coil fork, the job splits into two decisions: which spring rate to run, and how to carry out the swap without guessing. The catalog gives you seven rates and a clear compatibility statement. It does not give torque values, oil volumes, or a step-by-step disassembly procedure, so treat those as information to get from Öhlins documentation rather than something to improvise.

What the RXF 36 Coil Fork Spring record confirms

  • Öhlins RXF 36 Coil Fork Spring: Fits Öhlins RXF Coil fork only. This is the hard gate for the whole job. Check your fork model before you compare spring rates.
    Öhlins RXF 36 Coil Fork Spring
    Öhlins RXF 36 Coil Fork Spring
  • Öhlins RXF 36 Coil Fork Spring: Spring rates are broken down to 0.9 N/mm (5 lbs./in), with ultra-fine steps intended to suit all rider weights. The granular steps mean you can move one rate at a time instead of jumping between widely spaced options.
  • Öhlins RXF 36 Coil Fork Spring: The spring is described as setting a new benchmark for spring rate accuracy and light weight for trail and all-mountain fork springs. That positions the part for trail and all-mountain use in an RXF Coil fork, which is the context for your rate choice.

The seven rates in the catalog

The available variants are all black and cover a wide spread. Read them as a ladder, because the 0.9 N/mm steps are what make coil fork spring rate setup practical.

  • 6.1 N/mm (35 lbs./in): The lightest rate listed, at the bottom of the range.
  • 7.0 N/mm (40 lbs./in): One step up from the lightest option.
  • 7.9 N/mm (45 lbs./in): A middle-low rate in the lineup.
  • 8.8 N/mm (50 lbs./in): Sits at the center of the seven-rate spread.
  • 9.7 N/mm (55 lbs./in): A middle-high rate.
  • 10.6 N/mm (60 lbs./in): Second-stiffest listed rate.
  • 11.5 N/mm (65 lbs./in): The stiffest rate in the supplied variant list.

A careful spring replacement sequence

The catalog does not include a service procedure, so the steps below cover the decisions and checkpoints the supplied evidence supports. Fill in the mechanical details from Öhlins service information for your RXF Coil fork.

  1. 1. Confirm the fork is an RXF Coil: The spring fits the Öhlins RXF Coil fork only. Identify the fork before ordering or opening anything.
  2. 2. Record your current setup: Note the spring rate currently fitted and your baseline sag measurement so you can compare after the swap. The catalog does not prescribe a sag target, so use the figure from your fork documentation.
  3. 3. Choose one rate step at a time: Because rates are spaced in 0.9 N/mm (5 lbs./in) increments, the next rate up or down is a controlled change. Avoid skipping several steps unless you have a clear reason.
  4. 4. Follow Öhlins service guidance for the swap: Torque figures, oil handling, and any special tools are not confirmed in the supplied catalog record. Do not substitute guesses for the manufacturer's procedure.
  5. 5. Re-measure sag and adjust from there: Use the same measurement method as your baseline. If the new rate does not land where you want, move one step rather than changing several variables at once.

How to think about sag without inventing a number

Sag is the checkpoint that tells you whether a coil fork spring rate setup is in the right zone, but the correct target depends on your fork, your riding, and Öhlins' specification for that model. The supplied product record does not state a sag percentage or a rider-weight-to-rate chart, so any specific number you see elsewhere should be checked against Öhlins documentation rather than treated as universal.

What the catalog does support is a method: establish a baseline, change one rate step, and re-measure the same way. The fine 0.9 N/mm breakdown exists precisely so that this iterative approach is possible. If you are between two rates, testing the nearer one first keeps the comparison meaningful.

When a spring swap is the right move, and when it is not

A coil spring change is a targeted fix, not a general tuning cure. Use this comparison to decide whether you are solving the right problem.

  • A spring swap makes sense if: You ride an Öhlins RXF Coil fork, your current rate is clearly outside the range you need, and you want to move in the fine 0.9 N/mm steps the catalog provides.
  • A spring swap is not the answer if: Your fork is not an RXF Coil model. The compatibility statement is explicit, and no amount of rate tuning will make this spring fit a different fork.
  • Pause before buying if: You do not yet know your baseline sag or your current spring rate. Without a reference point, a new spring is a guess rather than a tuning step.

What the supplied information does not cover

The catalog record confirms compatibility, the rate ladder, and the intended trail and all-mountain context. It does not confirm installation torque, oil volume or weight, seal or tool requirements, a sag specification, or a rider-weight recommendation for each rate. Those details are not evidence that the product lacks them; they simply are not part of the supplied record.

Plan your Öhlins RXF 36 coil spring install around the information you can verify: the fork model, the rate you are moving from and to, and a repeatable sag measurement. For the mechanical procedure, use Öhlins service documentation for your RXF Coil fork so the swap stays within the manufacturer's guidance.

Relaterede artikler

Customer Service
Hjem
Produkter
Kurv
Profil